Enterprise - 1935 Six Meter

Summer 2011

2011-09-15T11:09:00.001-04:00

Finally, in the water.

2011-03-22T19:38:00.007-04:00

After nearly 20 years out of the water, Vinnia was re-launched in August of 2010, just in time for her 75th birthday. (sorry for the delay in updates.) The good news is that all the major repairs seemed to hold up well, with no leaks! I kept her in the water until mid-october, and viewed the short season as a two month shakedown cruise. With the help of my crew, I was able to assess the setup of the boat and make a good plan for some off season adjustments. These tweaks should make her perform better and a whole lot easier to sail.

We also managed to race her once in a DYC club race, and won! It was very satisfying after all the time I had to invest to get her back in the water.

Vinnia was re-christened "Enterprise" in an elaborate ceremony at the Detroit Yacht Club that was attended by family and friends. Looking forward to a great 2011.

Getting Close

2010-05-26T13:56:00.007-04:00

Work on the Six Meter is progressing nicely. I've got the underwater profile restored to the classic configuration. The new rudder is almost complete. New deck structure almost complete. Mast step repairs complete. Stem repairs complete. Steel floors reinstalled. Broken frames repaired. Here are some photos.

A lot going on in this photo. Notice the underwater profile restored to the Rule 2 Classic configuration. Rudder is temporarily hung. Aft deck is removed. New deck supports at midship - this structure separates the fore and aft cockpits and is where the mainsheet winch and the running back winches will be located.

Helpers! Steve Grimes and Joel Kar showed up to lend a hand. Notice Joel in the background wearing every type of protective equipment known to man, while Steve chooses to "tough it out."

New Rudder being built.

THE CLOCK IS TICKING!

2010-04-26T13:42:00.005-04:00

Making great progress on the boat in the last couple months. I'm shooting for a late may/early June launch.

The mast was picked up by the guys at Offshore Spars today. They evaluated the mast and rigging and pointed out some areas for concern that are now being repaired / replaced. The aluminum mast that came with the boat had never actually been on the boat. Bud (previous owner) broke the wooden mast for the last time, ordered this new aluminum mast, but never got a chance to put it on the boat. Coincidentally, he actually purchased this new mast from Offshore about 20 years ago, the same guys that are doing the work on it.

Al and Karl from Doyle sails are scheduled to come out and measure me for some new sails this week.

I did run into some problems in the stem, that were the result of corrosion from a metal fastener. A portion of the stem was rotted out in about the last 3 feet of the stem where it joins the keelson. The tricky part was that only about a 3/4" wide portion of the 2" x 4" stem was bad, right in the middle. Tearing out the whole stem, or even the last 3 foot section with the problem, would have caused considerable damage to the boat, since all the planking and frames connected to the stem in that area were very sound. I decided to remove the 3/4" x 3ft section that was bad, and put a new piece of oak in that section. Then I "sistered" the almost the entire stem with a new piece of 2" x 4" x 10 ft oak. While I realize that this will add a little weight, it should be a sound repair for a couple years, until I get time to do a proper repair.

The new keelson is in place and looks great.

I've got my crew lined up for a little fiberglass party in a couple weeks.

The deck is repair is about half done.

I've got four frames repaired, with about six more to go. I repaired these frames by removing the bad section, and laminating oak strips in place, and overtop of a scarf joint on the existing good portion of the frame. It's an easy job, but I need another pair of hands to finish it up. Doing the first four repairs solo, was way more difficult than it should have been.

More Repairs

2010-04-26T13:11:00.014-04:00

Two Halves of Keelson.
Top and bottom of each section bolted together and bonded with 3M 5200

Keelson Assembled - Top view
Notice stainless studs sticking out to accept metal supports in boat.

Half of Keelson installed. 3M 5200 to keep the water out.

New mast step supports over repaired stem

Top view
mast step supports and stem repair

BUILDING A NEW KEELSON

2010-02-13T17:17:00.002-05:00

Building a new keelson presented some real challenges that took a great deal of thought to overcome. The first challenge is that all seven keelbolts are on different angles from one another. This made is impossible to take a piece of wood, drill the holes, and slip it over the keel bolts. What we decided to do was to build the new keelson with a seam in the middle. Another reason for this decision was the difficulty in finding a piece of white oak that was 14 inches wide by 14 ft long.

The keelson was built out of four pieces of white oak measuring 1.75" x 7" x 14ft. We stacked two boards and fastened them together to create a board that was 3.5" x 7" x 14ft. Then we set the boards next to the keel bolts and traced then. Next, I took a router with a 1.25" half round bit and routed out half the hole for each keel bolt, and repeated the process on the other board.

Once we got two boards in place, they were fastened together with 1/2" stainless steel rod. When we put them in place for the final time, we will epoxy everything together also.

Now the outline of the inside of the boat and the keel need to be traced onto the boards, and the boards trimmed to size

more to come.

Keelson Out!

2010-02-03T10:03:00.003-05:00

Removed the keelson last weekend, and it came out quite easy. It was really in bad shape. Notice the angled keelbolts. Adds a little wrinkle to replacing the keelson.

WE HAVE LIFTOFF!

2010-01-25T14:13:00.011-05:00

We successfully lifted the boat about 5-1/2" last weekend in preparation for replacing the Keelson.

In both photos you can see the keel bolts and the exposed keelson, which is in pretty bad shape. In the the photo above, the first 12" of the keelson has been removed.

Here is how we did it. We build two separate cradles on forward and behind the existing cradle. These were build with 4x4's with bottle jacks underneath for lifting.

We also built a lifting frame over the boat out of 6x6's (see one of the photos below,) with a 3 ton chain fall hoist attached. Then we placed a 10ft 6x6 inside the boat in the same direction as the keel, that was attached to the chain fall. On top of this 6x6, were 4x4's running perpendicular to the 6x6. These ends of the 4x4's were tucked underneath the sheer clamps on each site of the boat. This system served to lift the middle of the boat, where the existing cradle was.

To say it went perfectly would be an understatement. Special thanks to my Dad and Joel Kar for all the help.